Skip to main content

Sanyo Washing Machine Error Codes

Amica Washing Machine Error Codes

 Amica Washing Machine Error Codes

Amica Washing Machine Error Codes

Code Direct cause Action taken by the controller Possible causes of the malfunction.
Error CodesProblem
E01No feedback signal from door interlock. After 15 seconds the E01 code is displayed and the wash programme is terminated. Washing machine door open. Faulty interlock. The door lock mechanism does not shift the interlock sensor far enough.
E02Filling time longer than 2 minutes The “Ready” LED flashes during the wash (which is not terminated). After the washing is completed the E02 error code is displayed. Further fillings above the pressure controller level are blocked. Low mains water pressure. Partia||y blocked inlet hose or valves.
E044 “Overfill” signal from pressure controller. The E04 error code is displayed, the pump is switched on and the wash programme is terminated.After1.5 minutes from sending of the “Reservoir empty” signal by the pressure controller the pump is switched off. If water is subsequently detected while the E04 error is indicated, the pump is restarted. So|enoid valves locked in the “Open” position. Large fluctuations in water pressure during the wash cycle. Wash cycle starts with closed water inlet which is then opened during the wash. Faulty pressure controller.
E05No signal from pressure controller 10 minutes after filling starts. The E05 error code is displayed and the wash programme is terminated. No water supply. Very low mains water pressure. Faulty solenoid valve. Faulty pressure controller. Control valve (washing machines with AquaSpray) locked in the “off" position E03. Water discharge time longer than 1.5 minutes.The “Ready” LED flashes during the wash (which is not terminated). The next spin cycle after discharging the water is restricted to 400 rpm. Partia||y blocked pump filter. Partia||y blocked discharge hose.
E06No “empty” signal from pressure controller 10 minutes after water discharging starts The E06 error code is displayed and the wash programme is terminated.Blocked pump.Blocked discharge hose. Control valve locked in the “on" position. Faulty pressure controller.
E07Signal (open contacts) from the floating sensor — water at the bottom of the drum. The E07 error code is displayed and the wash programme is terminated. The pump is switched on and then switched off 1,5 minutes after the “Reservoir empty" signal is sent. Water leak from the bathtub or hoses. Faulty sensor.
E08Input voltage outside the range of 160-253V, 50/60Hz. The E08 error code is displayed, washing cannot be started. After resetting, the error is indicated again if the cause is not rectified. Incorrect mains voltage.
E10Water injecting problem while washing. Check if the water pressure is too low Straighten the water pipe Check if the inlet valve filter is blocked.
E11Malfunction of the door interlock triac. After 2 seconds the E11 error code is displayed and the wash programme is terminated. Faulty electronic circuit board.
E12Water overflow. Restart the washer
E21Motor blocked: voltage is fed to the motor but there is no signal from the rate generator. The E21 error code is displayed and the wash programme is terminated. Faulty motor (rate generator, thermal switch or winding). Motor connection block removed. Therma| switch open clue to motor overheating.
E21Overtime water draining. Check if the drain hose is blocked.
E22Motor triac shorted — there is a signal from the rate generator even though no power is supplied to the motor. The E22 error code is displayed and the wash programme is terminated. Faulty electronic circuits (the error may occasionally be caused by a heavily unbalanced load such as a blanket or dressing gown)
E30Door is not closed properly. Restart after the door is closed Check if the clothes is stuck.
E31Temperature sensor shorted The wash programme is not terminated and after its completion the E31 error code is displayed. Faulty temperature sensor.
E32Temperature sensor open The wash programme is not terminated and after its completion the E32 error code is displayed. Faulty temperature sensor.
E42Time to unlock the door of more than 120 s.The error occurs at the end of the washing, if after the washing the door is not
unlocked within 2 minutes. The washing machine shows E42 error and another cycle cannot be started before the error signal is reset. door lock damaged. door is locked mechanically.
E51Incorrect data in program's memory. Displayed as error code, wasching machine start inoperable. Programmer damaged ( processor).
E52Incorrect data in configuration's memory Displayed as error code, wasching machine start inoperable. Programmer damaged ( processor).
E53Input circuit EMC errors Displayed as error code, washing machine start inoperable. Programmer damaged ( processor)
E54Autotest's errors Displayed as error code, wasching machine start inoperable. Programmer damaged;damaged circuit NTC.

The fault indicator lights

The washing machine indicates error codes to help locate minor operating faults and identify their cause. An error is indicated by LEDs on the control panel [Ready/ Start/Pause]. The appliance interrupts operation upon encountering an error.

The fault indicator lights
The fault indicator lights

Troubleshooting

The start of the appliance does not work or it stops during operation. First try to find a solution to the problem, If not, contact the service centre.

Description: Washing machine cannot start up

Reason: Door is not closed properly

Solution: Restart after the door is closed Check if the clothes is stuck

Description: Door can’t be opened

Reason: Washer’s safety protection design is working

Solution: Disconnect the power, restart the product

Description: Water leakage

Reason: The connection between inlet pipe or outlet hose is not tight

Solution: Check and fasten water pipes. Clean up outlet hose

Description: Detergent residues in the box

Reason: Detergent is dampened or agglomerated

Solution: Clean and wipe the detergent box

Description: Indicator or display does not light

Reason: Disconnect the power PC board or harness has connection problem

Solution: Check if the power is shut down and the power plug is connected correctly

Amica Washing Machine Manual PDF

Popular posts from this blog

GE Washing Machine Error Codes

  GE Washing Machine Error Codes GE Appliances Front Load Washer: Fault Codes Solution E22 Fill timeout -No fill/slow fill. Fill time exceeds 8 minutes. Check water valve functions. E23 Flood protect drain. In run state, any time the overflow be detected. Check water valve or water sensor. E31 Drain timeout. Slow drain: 1. Machine will have water. 2 Not full. Check drain pump - t05. E38 Dispenser error. Correct reservoir is not found and 8 switches are seen when motor is running. E39 Dispenser timeout. No switches found in 45 seconds. Check dispenser - t12 E42 Drive motor. Motor excess current draw. Check drive motor - t10 tumble, t11 spin, t13 spin. E45 No speed feedback. Motor speed lost. Check Motor - t10 tumble, t11 spin, T13 spin. E46 Drive motor - over temperature. Inverter over temperature. Power down (unplug) washer, wait 30 seconds and retry - use whites cycle sanitize temperature - if reoccurs, replace drive motor. E47 Heat sink - over temperature. Inverter over temperatu...
Read more

Haier Washing Machine Error Codes

  Haier Washing Machine Error Codes When the  washer  senses an error all machine operations will stop, a series of 4beeps will sound and an  error code  will be shown in the Estimated Time Remainingdisplay. Error Codes Solutions Err1 Door is not properly shut. Shut the door properly Err2 Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel Err3 Temperature sensor not properly connected or damaged. Contact the maintenance personnel. Err4 Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel Err5 Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose ...
Read more

Sanyo Washing Machine Error Codes

  Sanyo Washing Machine Error Codes When the following problems occur, the microcomputer will detect the abnormal condition and an electronic buzzer sounds for approximately 10 seconds and digital display indicates flash as shown below. Error Codes Problem U4 The washer does not spin. Close the Washer Lid. U3 The washer does not spin. Check whether the laundry is clumped on one side of the Wash/ Spin Tub or not. Check whether the Washer is on the level surface or not. U5 Does not wash. Check whether the Child safety mode is set or not. Close the Washer Lid. E1 Water does not flow into tub or water flow is slim. . Turn the water supply faucet on. Check whether the water supply has been cut off or not. Check whether the metal filter of the Water Inlet is clogged or not. Check whether the washer has been freezing or not. E2 Water does not drain out. Put down the Drain Hose from the hookhole. Check whether there is anything wrong with the Drain Hose or not. Check the Drain Hose for any...
Read more