The vast majority of failures and faults that occur in daily use of the machine can be eliminated personally. In many cases time and costs could be saved without necessarily having to contact The manufacturer srl authorized technical service centre. The following table will aid to identify and possibly eliminate the causes of failure/malfunction.
Daewoo Washing Machine Control Panel
Troubleshooting
All repairing operations required for your machine should be carried out by our authorised service provider.If your machine requires a repair or if you cannot remove the fault by the help of the information provided as follows:
Unplug your machine.
Turn the water faucet off.
Problem
Possible Solution
The door does not open
Make sure the red pilot lamp turns off
Make the special function SOAK or RINSE HOLD is not activated
Push the door from the door locking side or give a slight tap and at the same time pull it to open
The is water on the floor
Make sure the red pilot lamp turns off
Make the special function SOAK or RINSE HOLD is not activated
Push the door from the door locking side or give a slight tap and at the same time pull it to open
The washing machine pelting in water even when it is off
Make sure the red pilot lamp turns off
Make the special function SOAK or RINSE HOLD is not activated
Push the door from the door locking side or give a slight tap and at the same time pull it to open
The machine vibrates noticeably
Ensure that the transportation screws have been removed during installation
Ensure using the correct detergent for washing machine
Make sure that the laundry is not amassed or knotted and that the spin speed is adequate for the laundry load. It so recommended that for excessive laundry load and less than half the nominal load capacity set the spin speed to low
Make sure the drain pump filter is not clean. Ensure that the drain pump is squashed and that the machine dranins effectively
Ensure that the machine is properly levelled on floor. It is recommeded that for any eventual feet imbalance compensation the feet must regulated and lock them in place with the locking knob ( see figure on page 10)
The machine does not turn on or start
Make sure that the power plug is inserted.
Make sure there is power in the socket.
Make sure that the selector switch, programme selector knob 1, is not in the OFF position.
Most problems are easily solved if you understand the cause. Check the following list for problem before calling for service. If the error mode such as IE, OE, UE were displayed on the control part, in order to solve these problem, first turn off the power of the washing machine and then turn on the power pressing Power button. If PFE error mode was displayed on the control part, in order to solve this problem, first turn off the power of the washing machine, second turn on the power pressing Power button, third press SPIN button and last press Start/Hold button.
Automatic Fault Warnings And What To Be Done
Your machine is equipped with the systems which are capa- ble of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-check- ing during washing operations.
Hisense Washing Machine Error Codes In case of any abnormal conditions are detected during running, turn off all loads except for door lock, and then the buzzer sounds to give an alarm. Error Codes Problem F01 Water inflow fault F03 Drainage fault. Not fully drained within 6 minutes. F04 Heating Error. The heater is out of order. Give an alarm after the washing course ends. F05 Electronic module fault, overflow or too much foam. F06 No Motor Speed Feefback Error. The rotation speed is not set as 0, but no rotation speed is detected within 3s or the rotation speed is below 20rpm, 5 attempts. F07 Motor SCR Short Circuit Error. 1. The rotation speed is not set as 0, but the measured rotation speed>set rotation speed+80, and last for 3 seconds 2. The rotation speed is set as 0, but the rotation speed rises rather than declines, exceeding 10 turns within 3 seconds. F08 Heater Circuit Error. The main control detected a heater circuit failure. This failure modes are checked before th...
Haier Washing Machine Error Codes When the washer senses an error all machine operations will stop, a series of 4beeps will sound and an error code will be shown in the Estimated Time Remainingdisplay. Error Codes Solutions Err1 Door is not properly shut. Shut the door properly Err2 Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel Err3 Temperature sensor not properly connected or damaged. Contact the maintenance personnel. Err4 Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel Err5 Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose ...
Maytag Washing Machine Error Codes Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. Error Codes Problem Sd/Sud Excess suds oL Overloaded Washing Machine uL Unbalanced load LF/Ld Water coming in or going out of the machine HC Hot and cold inlet hoses haven't been installed correctly dL Lid cannot lock lid Lid is open dU If objects on top of the washer lid prevent it from unlocking dEt Detergent dispenser cartridge isn't detected E01, F01 E01 F01 appears due to a sharp voltage drop in the electrical network – both with increasing and decreasing. F08, E01 Water supply problem F09, E01 Drain pump system error F05, E02 Door isn't locking properly F07, E01 Motor is having a problem turning the washer drum F##/F##, E System error. To clear the code, press the "Start/Pause" or "Power/Cancel" button. FH FH No Water Entering Machine or Pressure Switch Failure. Maytag Washing M...
