Skip to main content

Sanyo Washing Machine Error Codes

Fisher & Paykel Washing Machine Error Codes

 

Fisher & Paykel Washing Machine Error Codes

Fisher and Paykel Washing Machine Fault Code List;Your washer is capable of diagnosing its own problems. If your washer gives a musical series of beeps every 5 seconds it is telling you that it has a problem which you can solve using the checklist below.Your washer sounds a musical series of beeps every 5 seconds and displays a user warning on the screen:

Error CodesProblem
no hotThe washer is not getting any hot water
no  CLDThe washer is not getting any cold water
no TAPThe washer is not getting any water
ouT oF bALThe washer is out of balance
SUd LoCThe washer has too many suds
LId LoC - LId oPnThe lid can’t lock or the lid is open
too FULThe washer is overloaded
PUr CUtThe washer has stopped
AdrThe washer has stopped

Problem: The washer is not getting any hot water.

Displayed As: no hot

What to do:

  • Hot water supply is not hot enough to maintain the wash temperature you have selected. Select a lower wash temperature
  • Inlet hose filters may be blocked and should be cleaned or replaced
  • There may be a kink in the hose. Undo the hose to remove the kink, and reattach. Damaged hoses should be replaced
  • Ensure hot tap has been turned on
  • Check inlet hoses are connected to the correct taps

Problem: The washer is not getting any cold water.

Displayed As: no  CLD

What to do:

  • Ensure cold tap has been turned on.
  • Inlet hose filters may be blocked and should be cleaned or replaced
  • There may be a kink in the hose. Undo the hose to remove the kink, and reattach. Damaged hoses should be replaced.
  • Check inlet hoses are connected to the correct taps
  • Cold water temperature exceeds recommended limits (refer to ‘Installation instructions – Water supply’)
  • The flow rate of the supply water is too slow. Refer to a registered plumber for advice

Problem: The washer is not getting any water

Displayed As: no TAP

What to do:

  • Ensure taps have been turned on
  • Inlet hose filters may be blocked and should be cleaned or replaced
  • There may be a kink in the hose. Undo the hose to remove the kink, and reattach. Damaged hoses should be replaced
  • The drain hose is too low or the drain hose is pushed into the standpipe too far and the water is siphoning out of the washer (refer to ‘Installation instructions – Drain hose’)
  • The flow rate of the supply water is too slow. Refer to a registered plumber for advice

Problem: The washer is out of balance

Displayed As: ouT oF bAL

What to do:

  • Wash load is out of balance. Ensure the washer is stationary. Manually redistribute the load
  • Check the washer is level (refer to ‘Installation instructions – Levelling instructions’)

Problem: The washer has too many suds

Displayed As: SUd LoC

What to do:

  • The washer has a suds build-up (too much detergent may have been used for the amount of soil in the load). Wait for suds to dissolve (about 20 min). Rinse clothes using a deep rinse
  • Check the standpipe height does not exceed 1200 mm
  • If the symptom persists, call your Fisher & Paykel dealer or Authorised Repairer

Problem: The lid can’t lock or the lid is open

Displayed As: LId LoC – LId oPn

What to do:

  • Make sure the lid is closed
  • Touch ”Star/Stop” (refer to ‘FabricSmart™ washer safety features – Lid lock’)
  • If the symptom persists call your Fisher & Paykel dealer or Authorised Repairer

Problem: The washer is overloaded

Displayed As: too FUL

What to do:

  • The washer is overloaded and can not agitate. Ensure the washer is stationary. Remove items until the remaining ones can move freely
  • Select a higher water level

Problem: The washer has stopped

Displayed As: PUr CUt

What to do: The power was cut to the washer. The washer will restart automatically. No action is required

Problem: The washer has stopped

Displayed As: Adr

What to do: The ”Start/Stop” or ‘Power’ button was touched and the washer was inactive for 3 minutes. The washer will automatically drain to a safe level. Touch any button to stop autodraining then touch to resume the wash cycle

Problem: The washer is on but the display is blank

What to do: The washer was unattended without starting a cycle for a period of time. Touch ‘Power’ to activate.

When a continuous series of beeps is sounded, all the lights turn off on the control panel and a number appears on the display, a fault has occurred. The washer will automatically enter this mode if a fault occurs. The fault code will be displayed as a number on the digital display. To stop the sound, touch any button and perform the following steps:

  • Turn your washer off at the power point.
  • Wait 1 minute and turn it back on.
  • Remove your wash load.
  • Perform a ‘Rinse’ cycle
  • If the washer will still not work you will be required to call a Fisher & Paykel Authorised Repairer to arrange service (refer to the ‘Customer Care’ section). Record the fault code number displayed and the serial number of your washer (located on the rear of the washer) before calling. The fault code will indicate to the repairer what the problem could potentially be

If a fault code is being displayed, you can still turn your washer off by touching ‘Power’

Fisher & Paykel Washing Machine Manual PDF

Popular posts from this blog

GE Washing Machine Error Codes

  GE Washing Machine Error Codes GE Appliances Front Load Washer: Fault Codes Solution E22 Fill timeout -No fill/slow fill. Fill time exceeds 8 minutes. Check water valve functions. E23 Flood protect drain. In run state, any time the overflow be detected. Check water valve or water sensor. E31 Drain timeout. Slow drain: 1. Machine will have water. 2 Not full. Check drain pump - t05. E38 Dispenser error. Correct reservoir is not found and 8 switches are seen when motor is running. E39 Dispenser timeout. No switches found in 45 seconds. Check dispenser - t12 E42 Drive motor. Motor excess current draw. Check drive motor - t10 tumble, t11 spin, t13 spin. E45 No speed feedback. Motor speed lost. Check Motor - t10 tumble, t11 spin, T13 spin. E46 Drive motor - over temperature. Inverter over temperature. Power down (unplug) washer, wait 30 seconds and retry - use whites cycle sanitize temperature - if reoccurs, replace drive motor. E47 Heat sink - over temperature. Inverter over temperatu...
Read more

Haier Washing Machine Error Codes

  Haier Washing Machine Error Codes When the  washer  senses an error all machine operations will stop, a series of 4beeps will sound and an  error code  will be shown in the Estimated Time Remainingdisplay. Error Codes Solutions Err1 Door is not properly shut. Shut the door properly Err2 Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel Err3 Temperature sensor not properly connected or damaged. Contact the maintenance personnel. Err4 Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel Err5 Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose ...
Read more

Hisense Washing Machine Error Codes

  Hisense Washing Machine Error Codes In case of any abnormal conditions are detected during running, turn off all loads except for door lock, and then the buzzer sounds to give an alarm. Error Codes Problem F01 Water inflow fault F03 Drainage fault. Not fully drained within 6 minutes. F04 Heating Error. The heater is out of order. Give an alarm after the washing course ends. F05 Electronic module fault, overflow or too much foam. F06 No Motor Speed Feefback Error. The rotation speed is not set as 0, but no rotation speed is detected within 3s or the rotation speed is below 20rpm, 5 attempts. F07 Motor SCR Short Circuit Error. 1. The rotation speed is not set as 0, but the measured rotation speed>set rotation speed+80, and last for 3 seconds 2. The rotation speed is set as 0, but the rotation speed rises rather than declines, exceeding 10 turns within 3 seconds. F08 Heater Circuit Error. The main control detected a heater circuit failure. This failure modes are checked before th...
Read more