Skip to main content

Sanyo Washing Machine Error Codes

Godrej Washing Machines Error Codes

 Godrej Washing Machines Error Codes and Troubleshootig

Godrej Washing Machines Error Codes

Error CodesMeaning
E1Water does not flow into wash/spin tub in 15 min. Machine will display - E1 error along with beeps.
E2If the water does not drain from machine the display will show -E2 error along with beeps after 5 minutes of starting drain operation
E3During spin operation if the lid is open machine will display -E3 error along with beeps.
E4If there is load unbalance for two times, the machine will try to balance it out automatically. If machine will goes into unbalance third time -E4 error will displayed
E5During child lock if the lid is open by the child, the machine will give -E5 error along with beeps
EEWater Pressure sensor not working properly during operation the machine will give error -EE with beeps.

Service Mode or Shortcut Key Function

Short keys: Ok + Start

Procedure: Press and hold for 3 sec

Functions: Line /service test mode: All Led on >> One by One Led on >> CW>>CCW >>Intake on>>Drain on.

Short keys: Left + Down

Procedure: Press and hold for 3 sec

Functions: Child lock

Short keys: Left + Right

Procedure: Press and hold for 3 sec

Functions: Line test mode: Drain On >>> One Minutes spin ON >> Power off.

Short keys: Left + up

Procedure: Press and hold for 3 sec

Functions: Fuzzy data>>> without water and cloths >> this will store the data automatically and power off.

Short keys: Ok

Procedure: Press and hold for 3 sec

Functions: save setting / Favourite

Godrej Washing Machines Display
Godrej Washing Machines Display-1
Godrej Washing Machines Display
Godrej Washing Machines Display-2

Troubleshooting

Before you call the service person, please check the following:

When your washing machine does not operate:

Check

  • Is there a power cut?

If there is a power cut while your machine is in operation, it will reset to REGULAR cycle when the power is restored. Please select the cycle you want and start the laundry operation once again.

  • Has your machine’s plug been inserted properly into the main power supply socket?
  • Is the water tap turned on properly?
  • Has the drainage hose been placed down to allow drainage?
  • Is the power switch ON?
  • Is the lid securely closed? (When beginning operation from the DRY cycle, your machine will not operate if the lid is open)

When your washing machine leaks:

Check

  • Is the hose coupling loose?
  • Is the nozzle loose?
  • Is the water supply hose connector clogged?
  • Is the water inlet nut loose?

When your washing machine makes an unusual noise:

Check

  • Is your washing machine installed on an incline or uneven surface?
  • Are there any match sticks, hairpins or metal objects being washed with the laundry?
  • Has a foreign object got caught under the pulsator? Switch the power OFF and remove the centre screw, then lift the pulsator and look underneath.
  • Is the load unbalanced, causing the basket to spin off-centre?

When your washing machine does not drain:

Check

  • Has DRY not been selected?
  • Is the drainage hose bent?
  • Has the drainage hose been placed down to allow proper drainage?
  • Is the drainage hose properly connected to your machine?

When your washing machine does not go to DRY cycle:

Check

  • Is your washing machine installed on an incline or uneven surface?
  • Is the lid closed? ‘ Is the laundry load unbalanced?
  • Is the warning light ON?

Don’t worry when…

-A small amount of water drains out of the drainage hose the first time you use your washing machine. This is merely the water left over from the performance inspection performed on your washing machine before it was shipped from the factory.

-Buzzing noises occur when the tub fills with water. They are caused by the operation of the water supply valve.

-Sloshing sounds are made by your machine during the DRY cycle.These are made by the water in the Liquid Balancing Ring which is meant to maintain balance of the Spin Tub and does not indicate a malfunction.

-When you restart your machine after opening the lid or pausing the machine during the DRY cycle, there may be a small pause before the machine begins to spin as the drainage valve opens. Also, when you start your machine immediately after stopping it, there will be a short pause. This happens for safe operation.

-If you press the pads when the machine is operating or paused, the machine may return to the beginning of the cycle and lengthen operating time.

-Your machine automatically corrects a load unbalance that occurs during the DRY cycle. If the unbalance is extremely bad, your machine will refill with water and agitate for a moment, and then the DRY cycle will resume.

-This will happen twice. If the load becomes unbalanced a third time, a buzzer will sound 60 times and the WATER LEVEL and CLEAN lamps will light alternater.This alarm also sounds when the water is not draining properly.

Godrej Washing Machines Manual PDF

Popular posts from this blog

GE Washing Machine Error Codes

  GE Washing Machine Error Codes GE Appliances Front Load Washer: Fault Codes Solution E22 Fill timeout -No fill/slow fill. Fill time exceeds 8 minutes. Check water valve functions. E23 Flood protect drain. In run state, any time the overflow be detected. Check water valve or water sensor. E31 Drain timeout. Slow drain: 1. Machine will have water. 2 Not full. Check drain pump - t05. E38 Dispenser error. Correct reservoir is not found and 8 switches are seen when motor is running. E39 Dispenser timeout. No switches found in 45 seconds. Check dispenser - t12 E42 Drive motor. Motor excess current draw. Check drive motor - t10 tumble, t11 spin, t13 spin. E45 No speed feedback. Motor speed lost. Check Motor - t10 tumble, t11 spin, T13 spin. E46 Drive motor - over temperature. Inverter over temperature. Power down (unplug) washer, wait 30 seconds and retry - use whites cycle sanitize temperature - if reoccurs, replace drive motor. E47 Heat sink - over temperature. Inverter over temperatu...
Read more

Haier Washing Machine Error Codes

  Haier Washing Machine Error Codes When the  washer  senses an error all machine operations will stop, a series of 4beeps will sound and an  error code  will be shown in the Estimated Time Remainingdisplay. Error Codes Solutions Err1 Door is not properly shut. Shut the door properly Err2 Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel Err3 Temperature sensor not properly connected or damaged. Contact the maintenance personnel. Err4 Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel Err5 Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose ...
Read more

Hisense Washing Machine Error Codes

  Hisense Washing Machine Error Codes In case of any abnormal conditions are detected during running, turn off all loads except for door lock, and then the buzzer sounds to give an alarm. Error Codes Problem F01 Water inflow fault F03 Drainage fault. Not fully drained within 6 minutes. F04 Heating Error. The heater is out of order. Give an alarm after the washing course ends. F05 Electronic module fault, overflow or too much foam. F06 No Motor Speed Feefback Error. The rotation speed is not set as 0, but no rotation speed is detected within 3s or the rotation speed is below 20rpm, 5 attempts. F07 Motor SCR Short Circuit Error. 1. The rotation speed is not set as 0, but the measured rotation speed>set rotation speed+80, and last for 3 seconds 2. The rotation speed is set as 0, but the rotation speed rises rather than declines, exceeding 10 turns within 3 seconds. F08 Heater Circuit Error. The main control detected a heater circuit failure. This failure modes are checked before th...
Read more