Skip to main content

Sanyo Washing Machine Error Codes

Hoover Washing Machine Error Codes

 Hoover Washing Machine Error Codes

Hoover Washing Machine Error Codes

Error CodesMeaning
Error 0Faulty module or wiring
Error 1Open circuit Door Interlock
Error 2Fill time out, Pressure stat or pressure chamber.
Error 3Drain time-out, blocked filter, Pressure stat stuck.
Error 4Anti flood Pressure stat, faulty inlet valve.
Error 5NTC fault or module.
Error 6Faulty module or wiring.
Error 7Motor fault.
Error 8Tacho fault.
Error 9Short circuit motor triac on module.
Error 10Programme Selector.
Error 12Communication error between boards and wiring.
Error 13Communication error between boards and wiring.
OModule Fault
1Door Interlock/Door Switch
2Filling time-out or Solenoid Valve etc.
3Pump time-out (3 mins) exceeded
4Overfill (i.e. Blocked air chamber/faulty solenoid valve)
5NTC/Heater fault
6Module fault
7Motor jammed/Drum Shaft jammed/Tacho generator fault
8Ditto
9Faulty TRIAC on main board
10Faulty program selector / wiring
11Faulty dryer board or wiring (Latest Interact models)
E:00Faulty Module (Coreboard)
E:01Door Interlock
E:02Fill time-out
E:03Drain time-out
E:04Anti-flood on Pressure s/w or Inlet valve blocked
E:05NTC fault
E:06Eeprom/Coreboard fault
E:07Motor jammed or Interlock fault
E:08Tacho fault
E:09Motor triac failure on Coreboard
E:10Motorised Selector s/w fault or open-circuit drum sensor device
E:11Open circuit dryer heater or Dryer NTC or Dryer Module
E:12Communication error between both boards
E:13Communication error between both boards
E:14Faulty Coreboard or water heater/NTC fault
E:15Coreboard not programmed
E:16Water heater element insulation fault
E:17No signal from tacho generator
E:18Faulty Coreboard or wiring
TR1Motor fault (Brushes - commutator)
TR2Hot solenoid valve
TR3Cold solenoid valve
TR4Door Interlock
TR5Drain Pump
TR6Wash (recycling) Pump
TR7Wash Programme Selector (Stepper Timer Unit)
HThe delay start is active.
L1, L2 or L3This is not a fault. When selecting a programme the letter 'L' followed by a number may appear in the display. This is normal and not an indication of a fault.
Hoover Washing Machine Control Panel
Hoover Washing Machine Control Panel

Cleaning and Routine Maintenance

Do not use alcohol-based scourers and /or thinners on the outside of your washing machine, just a wipe with a damp cloth will suffice. The washing machine needs very little maintenance:

  • Cleaning the drawer compartments.
  • Cleaning the filter.
  • Cleaning the door glass.

Cleaning the drawer

Clean the compartments occasionally to remove detergents and additives.

  • To do this you just need to pull the drawer out firmly from the machine, but without forcing it.
  • Clean the compartments and the syphon cap under running water.
  • Replace the drawer.

Cleaning the filter

The washing machine is fitted with a special filter to prevent items such as coins, buttons, etc. blocking the discharge hose. These may be retrieved by:

  1. Removing the kickplate by gently pulling it from the bottom in an outwards and upwards direction.
  2. Use the kickplate to collect the water still in the filter.
  3. Turn the filter anticlockwise, remove it and clean it.

After cleaning, return to it’s original position and lock by turning clockwise. Replace the kickplate. We recommend that the filter be cleaned frequently, at least once a month.

Hoover Washing Machine Troubleshooting

Before calling GIAS Service for technical advice please run through the following checklist. A charge will be made if the machine is found to be working or has been installed incorrectly or used incorrectly.

PROBLEMCAUSEREMEDY
Does not work on any programmePlug not in socket.Plug it in.
Not switched on.Switch on.
Power failure.Check and refer to ‘Power Failure’ section.
Fuse blown.Check.
Door open.Close door.
RCD tripped (trip switch)Reset RCD.
Does not fill with waterWater supply turned off.Turn on water supply.
Programme selector not correctly positioned.Position programme selector correctly.
Water does not drain awayKink in discharge hose.Straighten discharge hose.
Foreign bodies in filter.Examine filter.
The machine has been plumbed in incorrectly.Check installation.
Water on floor around the washing machine.Leaking gasket between tap and water inlet hose.Replace gasket and tighten connection.
Strand of clothing or dirt between door rubber gasket and door glass.Re-load the machine and keep rubber door gasket/door glass clean.
Incorrect plumbing.Check plumbing.
Does not spin.Water has not yet drained away.Wait a few minutes for machine to empty.
‘Spin Cancel’ option selected.Check.
Unbalanced load.Rearrange load evenly.
Machine vibrates a lot during spin.Washing machine not completely level.Adjust the special adjustable feet.
Load not distributed evenly.Rearrange the laundry evenly.
Transit brackets not removed.Remove transit brackets.
Door will not open.Two minutes have not elapsed since the programme finished.Wait two minutes.
The control knob turns a full circle quickly during a programme.The control knob was not in the expected position when automatically checked by the machine.Note: This action is normal if the knob has been moved accidentally during a cycle.

Hoover Washing Machine Manual PDF

Popular posts from this blog

GE Washing Machine Error Codes

  GE Washing Machine Error Codes GE Appliances Front Load Washer: Fault Codes Solution E22 Fill timeout -No fill/slow fill. Fill time exceeds 8 minutes. Check water valve functions. E23 Flood protect drain. In run state, any time the overflow be detected. Check water valve or water sensor. E31 Drain timeout. Slow drain: 1. Machine will have water. 2 Not full. Check drain pump - t05. E38 Dispenser error. Correct reservoir is not found and 8 switches are seen when motor is running. E39 Dispenser timeout. No switches found in 45 seconds. Check dispenser - t12 E42 Drive motor. Motor excess current draw. Check drive motor - t10 tumble, t11 spin, t13 spin. E45 No speed feedback. Motor speed lost. Check Motor - t10 tumble, t11 spin, T13 spin. E46 Drive motor - over temperature. Inverter over temperature. Power down (unplug) washer, wait 30 seconds and retry - use whites cycle sanitize temperature - if reoccurs, replace drive motor. E47 Heat sink - over temperature. Inverter over temperatu...
Read more

Haier Washing Machine Error Codes

  Haier Washing Machine Error Codes When the  washer  senses an error all machine operations will stop, a series of 4beeps will sound and an  error code  will be shown in the Estimated Time Remainingdisplay. Error Codes Solutions Err1 Door is not properly shut. Shut the door properly Err2 Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel Err3 Temperature sensor not properly connected or damaged. Contact the maintenance personnel. Err4 Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel Err5 Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose ...
Read more

Hisense Washing Machine Error Codes

  Hisense Washing Machine Error Codes In case of any abnormal conditions are detected during running, turn off all loads except for door lock, and then the buzzer sounds to give an alarm. Error Codes Problem F01 Water inflow fault F03 Drainage fault. Not fully drained within 6 minutes. F04 Heating Error. The heater is out of order. Give an alarm after the washing course ends. F05 Electronic module fault, overflow or too much foam. F06 No Motor Speed Feefback Error. The rotation speed is not set as 0, but no rotation speed is detected within 3s or the rotation speed is below 20rpm, 5 attempts. F07 Motor SCR Short Circuit Error. 1. The rotation speed is not set as 0, but the measured rotation speed>set rotation speed+80, and last for 3 seconds 2. The rotation speed is set as 0, but the rotation speed rises rather than declines, exceeding 10 turns within 3 seconds. F08 Heater Circuit Error. The main control detected a heater circuit failure. This failure modes are checked before th...
Read more