Logik Washing Machine Error Codes

When the error code is on, the washing machine will sound. If a fault cannot be rectified or a repair is required, then:

1. Press the Power button to switch off the washing machine and then pull out the mains plug.
2. Turn off the tap and call for service.

Error Codes	Meaning
E1	Locking door function malfunction. What to do: Re-close the door.
E2	Draining malfunction. What to do: Rinse the filter of draining pump, examine whether the drainpipe is blocked.
E3	Temperature pickup malfunction. What to do: Ask a qualified technician to repair it.
E4	Heating malfunction (display after procedure operation). What to do: Ask a qualified technician to repair it.
E5	Water intake malfunction. What to do: Check the water pressure is too low or water supply is cut off.
E7	There is a lot of foam in the washing machine or motor failure. What to do: Select and run a programme to fill and then drain the washing machine or ask a qualified technician to repair it.
E8	Water overflow. What to do: Ask a qualified technician to repair it.
E10	Inlet water overtime of 7 min. What to do: Open the water tap, to check if the inlet hose is squashed or kinked, check the filter in the inlet valve is blocked or not; check if the water pressure is too low.
E21	Overtime 3 min of the drainage. What to do: Check if the drain pump is blocked.
E30	The door has not been closed over 3 times. What to do: Check if the door of the washing machine is closed. Check if the clothes is pinned by the door.
U6	Washing machine has an unbalanced load protection function. When unbalanced weight is greater than allowable maximum, the washing machine will not spin and will run at a low speed to avoid abnormal vibration and noise.

Logik Washing Machine Control Panel

Logik washing machine problems:

Display	Fault	What to do:
	Locking door function malfunction.	Re-close the door.
	Draining malfunction.	Rinse the filter of draining pump, examine whether the drainpipe is blocked.
	Temperature pickup malfunction.	Ask a qualified technician to repair it.
	Heating malfunction (display after procedure operation).	Ask a qualified technician to repair it.
	Water intake malfunction.	Check the water pressure is too low or water supply is cut off.
	There is a lot of foam in the washing machine or motor failure.	Select and run a programme to fill and then drain the washing machine or ask a qualified technician to repair it.
	Water overflow.	Ask a qualified technician to repair it.
	Washing machine has an unbalanced load protection function. When unbalanced weight is greater than allowable maximum, the washing machine will not spin and will run at a low speed to avoid abnormal vibration and noise.	In case washing 1 piece of laundry (carpet, bed sheet, table sheet, etc) make it symmetrical inside the drum. Lower the wet weight of laundry pieces by wringing manually and placing them back in the drum in symmetrical position. Take out and then reposition the laundry pieces inside the washing machine in a more balanced position on the inner wall of the drum. Add 1 or 2 pieces of laundry into the drum to reduce the unbalanced load effects. Restart the spin cycle by choosing Spin programme. In case the failure persists, please ask a qualified technician to repair it.

How to Set the Child Lock?

The Child Lock prevents children from stopping programmes accidentally. It only locks the control buttons not the Programme Dial.

1. Switch the washing machine on.
2. When the washing machine is operating, press and hold the Delay button and Speed buttons at the same time for 3 seconds to set the child lock. The LEDs on the function buttons will blink to indicate that the child lock is active.
3. If a function buttons is pressed when the child lock is active, the function button lights will flash to indicate the child lock is active.
4. To deactivate the child lock, press and hold the Delay and Speed buttons until the function buttons stop flashing.

1. Deactivate the cild lock when the programme ends.  2.Your machine will deactivate the spin speed selector and function buttons when the child lock is activated.

Logik Washing Machine Troubleshooting

Trouble	Solution
Buttons don’t work	Child lock is activated. Deactivate the child lock function.
Door doesn’t open	The water temperature or level could be too high.
If you start a wrong programme accidentally	First press Start/Pause button or turn the Programme Dial to 0(Off) position. Secondly turn the Programme Dial to the correct programme, spin speed or optional function you want. Press the Start / Pause button to start the new programme. (Note: We suggest that you do not change the programme after the machine has been running for 3 minutes.)
Unusual odour	Rubber parts and the motors may give off a smell when you first start using the washing machine, but this goes away over time. You should wash the drum once a month.
You can’t see any water	This is normal: The water level is below the window
There’s no water going into the washing machine.	The water tap might be turned off.
There’s only a small amount of water.	If you have paused the programme and you restart, the washing machine may drain some water. Don’t pour water in through the door.
Water adds up during washing.	This is normal: water is supplied automatically as the level lowers, and with heavy loads the water may fill up repeatedly.
The washing machine does not spin.	The rinse hold may be active. Press the Rinse Hold button to continue. If a small load is in the washing machine, it may be detected as an unbalanced load and may stop spinning after a number of attempts. Select the manual spin.
There’s no water going into the washing machine during rinse operation.	Before rinsing, the washing machine spins to drain water remaining from the wash. The water will fill up after that.
During the spin-dry, the drum stops and rotates several times.	This is normal. The washing machine has detected an unbalanced load and is trying to correct it.
Foam and water remain in the door or door seal.	Although foam and water may remain, it does not have any influence on the performance of a rinse.
Spin starting is repeated.	This is normal. Although spin starting may be repeated, it is a function made to spin quietly.
There’s a lot of foam	The amount of foam can vary depending on the temperature, level and softness of your water.
There’s a residue of powder detergent at the end of the wash	This can happen if you’ve put powder detergent directly into the drum - you must put it in the detergent drawer.
There’s a noise when the water drains away	This is normal, it’s the pump starting and stopping.
The electricity supply cuts out while the washing machine’s on	The washing machine will stop (do not open the door if the machine is full of water). When the power comes back on, the washing machine will continue the programme.
The water supply is disrupted	When the water comes back on, it may be impure at first. You’ll need to disconnect the water-supply hose and drain any impure water through the tap before using your washing machine again. Remember to re-connect the water supply hose first.
Excessive foam in the detergent drawer	Press the Start/Pause button. Change the programme to the Rinse selection to manually rinse and drain the drum. Use the correct amount of detergent next time.

Logik Washing Machine Problems

Logik Washer Wiring Circuit

Models: 

• L612WM13
• L612WMS13
• L612WMB14
• L812WM12
• L614WMS12

Logik Washing Machine Manual PDF 1

Logik Washing Machine Manual PDF 2

Logik L612WM15 Washing Machine Manual PDF