Skip to main content

Sanyo Washing Machine Error Codes

Midea Washing Machine Error Codes

 Midea Washing Machine Error Codes

Midea Washing Machine Error Codes

The following table is a list of the fault indicators and corresponding alarms.
Midea Washing Machine Display
Midea Washing Machine Display
Error CodesSolution
F0Alarm for the power cut off failed. 1. Cut off power and start it 5 minutes later. 2. Report for repairing
F2Alarm for reading EEPROM failed. Report for repairing.
F8Alarm for water level sensor. Report for repairing.
E1Alarm for abnormal water intaking. 1. Open the water tap. 2. Hydraulic pressure is low, increase inlet water amount.
E2Alarm for water drain has not finished. Check if water drain hose is placed correctly. Clean the stem.
E3Alarm for lid not closed before spin. Please close the door lid.
E4Alarm for washing stay at one side. Placed the washing equably.
E5The water fills too much to exceed its preset level.
E6Not normally open or unlocked door. The door can be open only by pull up the power when the door is locked, and it can power-off and alarm-cleared by press the power key when the door lock is open.
E10Inlet water overtime. Open the water tap,to check if the inlet hose is squashed or kinked,check the filter in the inlet valve is blocked or not;check if the water pressure is too low.
E12Overflow protection. The water level exceed overfloow level. The machine lock the door, close inlet valve, motor stop working, drain water in error status. 1. Restart machine. 2. Change inlet valve.
E21Overtime of the drainage. Check if the drain pump is blocked.
E30The door has not been closed. Check if the door of the Washing machine is closed check if the clothes is pinned by the door.
E50Others. Please call up the service line if there is any other problem.
E60Error E60, E61, E62 etc. generally refers to a heating problem with the machine
HUHigh voltage protection ≥ 270±10V. The power cut off automatically.

Troubleshooting

If the clothes washer does not perform as expected, malfunctions, or an alarm is sounding, please check the following list of possible solutions.

Midea Washing Machine Display
Midea Washing Machine Display
TroublesReasonSolution
Door will not openThis is the machine’s safety protection.Disconnect the power, wait a few minutes, door will then open.
Heating faultHeating element damaged.

  • Can only wash without heat.

  • Contact the service centre promptly.

Water leakage

  • The connection between inlet pipe or outlet hose and tap or washing machine is not tight.

  • Drain pipe is blocked.


  • Check and fasten water pipes.

  • Clean up outlet hose.

  • Arrange a service person to repair if necessary.

Water overflowing from bottom of machine

  • The inlet hose is not connected firmly.

  • Drain hose has a leakage.


  • Fix the inlet hose in place securely.

  • Replace the drain hose.

Indicator or display does not light

  • Power is disconnected.

  • PC board has problems.

  • Harness has connection problem.

Check if the power is shut down and power plug is connected correctly. If not, please contact customer care.
Detergent residue in the dispenser drawerWashing powder is dampened and agglomerated.

  • Clean and wipe the drawer.

  • Use liquid detergents or detergents especially for front load washers.

Poor washing effects

  • The clothes are heavily soiled.

  • Insufficient detergent quantity.


  • Select appropriate wash program.

  • Add the proper detergent quantity according to instructions on the detergent package.

Washing machine will not start up

  • Check if the door is closed tightly.

  • Check if power plug is inserted correctly.

  • Check if water supply tap is opened.

  • Check if button “Start/Pause” is pressed.

  • Check if button “Power” is pressed.

Abnormal noises and vibrations

  • Check if the transit bolts have been removed.

  • Check if installed on solid and level floor.

  • Check if the feet of the washing machine are leveled correctly.

  • Check for hair clips or metal articles inside the drum.

Cleaning & Maintenance

Cleaning the drain pump lint filter

According to the soil level within the cycles and frequency of the cycles, you have to inspect and clean the filter regularly.

The pump should be inspected if the machine does not empty and/or spin.The machine makes an unusual noise during draining due to objects such as safety pins, coins etc. blocking the pump.

  1. Prepare a dish or bucket to catch any excess water remaining in the drain pump. Place under drain pump before continuing.
  2. Open the service panel and unscrew the drain pump cover. Drain any water into the dish or bucket. Mop up any spillage with a rag.
  3. Remove any debris and obstructions from the drain pump filter.
  4. Replace and tighten the drain pump cover before closing the service panel.
Midea Washing Machine Clean Filter
Midea Washing Machine Clean Filter

Please check the points below after maintenance:

  • Is there any damage to the power lead?
  • Can the power plug be inserted into the power socket correctly?
  • Is the power plug and /or lead heating up?

Midea Top Load Washing Machine Manual PDF 1

Midea Washing Machine Manual PDF 2

Midea Washing Machine Manual PDF 3

Popular posts from this blog

GE Washing Machine Error Codes

  GE Washing Machine Error Codes GE Appliances Front Load Washer: Fault Codes Solution E22 Fill timeout -No fill/slow fill. Fill time exceeds 8 minutes. Check water valve functions. E23 Flood protect drain. In run state, any time the overflow be detected. Check water valve or water sensor. E31 Drain timeout. Slow drain: 1. Machine will have water. 2 Not full. Check drain pump - t05. E38 Dispenser error. Correct reservoir is not found and 8 switches are seen when motor is running. E39 Dispenser timeout. No switches found in 45 seconds. Check dispenser - t12 E42 Drive motor. Motor excess current draw. Check drive motor - t10 tumble, t11 spin, t13 spin. E45 No speed feedback. Motor speed lost. Check Motor - t10 tumble, t11 spin, T13 spin. E46 Drive motor - over temperature. Inverter over temperature. Power down (unplug) washer, wait 30 seconds and retry - use whites cycle sanitize temperature - if reoccurs, replace drive motor. E47 Heat sink - over temperature. Inverter over temperatu...
Read more

Haier Washing Machine Error Codes

  Haier Washing Machine Error Codes When the  washer  senses an error all machine operations will stop, a series of 4beeps will sound and an  error code  will be shown in the Estimated Time Remainingdisplay. Error Codes Solutions Err1 Door is not properly shut. Shut the door properly Err2 Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel Err3 Temperature sensor not properly connected or damaged. Contact the maintenance personnel. Err4 Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel Err5 Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose ...
Read more

Sanyo Washing Machine Error Codes

  Sanyo Washing Machine Error Codes When the following problems occur, the microcomputer will detect the abnormal condition and an electronic buzzer sounds for approximately 10 seconds and digital display indicates flash as shown below. Error Codes Problem U4 The washer does not spin. Close the Washer Lid. U3 The washer does not spin. Check whether the laundry is clumped on one side of the Wash/ Spin Tub or not. Check whether the Washer is on the level surface or not. U5 Does not wash. Check whether the Child safety mode is set or not. Close the Washer Lid. E1 Water does not flow into tub or water flow is slim. . Turn the water supply faucet on. Check whether the water supply has been cut off or not. Check whether the metal filter of the Water Inlet is clogged or not. Check whether the washer has been freezing or not. E2 Water does not drain out. Put down the Drain Hose from the hookhole. Check whether there is anything wrong with the Drain Hose or not. Check the Drain Hose for any...
Read more