Skip to main content

Sanyo Washing Machine Error Codes

Panda Washing Machines and Dryers Error Codes

 

Panda Washing Machines and Dryers Error Codes

You can solve common appliance problems easily, saving you the coast of possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer.

Problem: Timer knob will rotate

Possible Cause: Not plugged in.

Problem: Dryer does not operate.

Possible Cause: The circuit breaker tripped or blown fuse.

Problem: Drum does not rotate

Possible Cause: Door is not closed

Problem: Laundry not completely dry

Panda Washing Machines and Dryer Control Panel
Panda Washing Machines and Dryers Control Panel

Possible Cause:

  • Clean the filter
  • Reduce the amount of clothing loaded in the dryer
  • Re-dry the loaded items
  • Ensure items are not knotted or bulked together
  • Dryer is not located in a well ventilated area

Problem: Hot air is not blowing out

Possible Cause: Is the timer incorrectly set on cold air

What to do: Set the timer to hot air

Installation

Panda Washing Machines and Dryers Installation
Panda Washing Machines and Dryers Installation

Install hoses for (For use faucet in kitchen and drain water in the sink)

  1. Remove the faucet filter or nozzle from your tap.
  2. Screw silver part of facet quick adaptor to the tap and tighten firmly. The adaptor has both female and male threads, choose one size that suits your tap.
  3. one end of inlet hose attaches to COLD connector on the back of washer, tighten with a wrench.
  4. The other end of inlet hose attaches to the silver adaptor which is already fixed on faucet.
  5. Hook the drain hose up to the sink. Make sure during washing, the drain hose must reach always at height of at least 30 inch (in the sink) to drain water out.
  6. Always choose “Cool” temperature on the control panel, but you could adjust your warm, hot, or cold water from your tap.

IMPORTANT

  1. Please directly connect the water inlet hose to Cold connector in the back of the washer
  2. Connect another end with faucet adaptor, then connect to the tap
  3. Choose the Cold Water Temperature ONLY. If choose Hot or Warm water temperature, it may cause the machine malfunction. However, you can always feel free to adjust the temperature on the tap.

Pre-Use Caution: Some small objects, such as coins or hair pin may possibly cause clogs for the drainage system. Before load clothes into the washer, please check with the pocket and remove all small objects from the pocket.

We guarantee all washers are brand new, if you find some water or watermark, it’s manufacture testing.

KEY FEATURES

  1. This washer is a space-saving design which makes your laundry easy and simple. It is perfect for Apartment, RV, Vacation Home, Dorm, and second washer for your house.
  2. Lager size 1.6cu.ft capacity allows you to fit up to 11 lbs. of cloth, electronic Touchpad controls and LED display, Delay start available, upgraded with an extra Control Lock option, regular 3 prongs 110 Voltage can be plugged anywhere, 2 built in rollers increase mobility for easy move around.
  3. Large See-through viewing lid and stainless steel tub, 3D waterfall, Pulsator generates strong and weak water flows
  4. 6 Washing Program provide flexible washing options: Normal, Quick, Heavy, Bulky, Delicate and Spin Only, Upgraded with an Extra Rinse Function
  5. 2 rear inlets for easy installation; Connect the washer directly to your faucet with the included quick connect adapter kit and hoses

Panda Washing Machines and Dryers Manual PDF 1

Panda Washing Machines and Dryers Manual PDF 2

Popular posts from this blog

GE Washing Machine Error Codes

  GE Washing Machine Error Codes GE Appliances Front Load Washer: Fault Codes Solution E22 Fill timeout -No fill/slow fill. Fill time exceeds 8 minutes. Check water valve functions. E23 Flood protect drain. In run state, any time the overflow be detected. Check water valve or water sensor. E31 Drain timeout. Slow drain: 1. Machine will have water. 2 Not full. Check drain pump - t05. E38 Dispenser error. Correct reservoir is not found and 8 switches are seen when motor is running. E39 Dispenser timeout. No switches found in 45 seconds. Check dispenser - t12 E42 Drive motor. Motor excess current draw. Check drive motor - t10 tumble, t11 spin, t13 spin. E45 No speed feedback. Motor speed lost. Check Motor - t10 tumble, t11 spin, T13 spin. E46 Drive motor - over temperature. Inverter over temperature. Power down (unplug) washer, wait 30 seconds and retry - use whites cycle sanitize temperature - if reoccurs, replace drive motor. E47 Heat sink - over temperature. Inverter over temperatu...
Read more

Haier Washing Machine Error Codes

  Haier Washing Machine Error Codes When the  washer  senses an error all machine operations will stop, a series of 4beeps will sound and an  error code  will be shown in the Estimated Time Remainingdisplay. Error Codes Solutions Err1 Door is not properly shut. Shut the door properly Err2 Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel Err3 Temperature sensor not properly connected or damaged. Contact the maintenance personnel. Err4 Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel Err5 Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose ...
Read more

Hisense Washing Machine Error Codes

  Hisense Washing Machine Error Codes In case of any abnormal conditions are detected during running, turn off all loads except for door lock, and then the buzzer sounds to give an alarm. Error Codes Problem F01 Water inflow fault F03 Drainage fault. Not fully drained within 6 minutes. F04 Heating Error. The heater is out of order. Give an alarm after the washing course ends. F05 Electronic module fault, overflow or too much foam. F06 No Motor Speed Feefback Error. The rotation speed is not set as 0, but no rotation speed is detected within 3s or the rotation speed is below 20rpm, 5 attempts. F07 Motor SCR Short Circuit Error. 1. The rotation speed is not set as 0, but the measured rotation speed>set rotation speed+80, and last for 3 seconds 2. The rotation speed is set as 0, but the rotation speed rises rather than declines, exceeding 10 turns within 3 seconds. F08 Heater Circuit Error. The main control detected a heater circuit failure. This failure modes are checked before th...
Read more